Introduction: Ryuk Costume
(Since I tend to get asked about selling the Shinigami, Rem and Ryuk have been sold. But hey, you can make your own!)
Everybody's favorite Shinigami.
Ryuk is a death god featured in the manga/anime/live-action-films called Death Note. Have no clue what I'm talking about? It's this guy right here! I based my costume mainly on an image from Takeshi Obata's Blanc et Noir (an art book by the artist of the Death Note manga. See previous link for the particular image I'm talking about).
This costume is made up of a long leather shirt, leather pants, leather boots, a pleather-and-leather belt, leather belt bag, leather notebook, 3 resin rings, 2 bracelets, earring, "arm skull", buckle, belt end, chain connector, pen, belt and notebook cross, shrink-plastic chain, staples and teeth, latex mask, resin eyes, "painted" and styled wig, and a whole lot of feathers. Everything was either made or heavily altered, including the boots.
The leather outfit was made of over 80 pieces of leather patch-worked together. I used an old ill-fitting trenchcoat, bought a few coats from Value Village and was given an old pair of pants from my brother in law. I took them all *completely* apart, so I was left with (mainly) rectangular pieces of leather. Individual pieces were drafted and cut out, given texture with a wood-burning tool and sewn to other pieces. Zippers, grommets, studs and cords adorned the pieces, along with kneepads and a spine (both of which were formed by soaking leather in water and leaving them around light bulbs and an ice cube tray). For the feather epaulettes, I pulled the tips of the feathers through fabric and dabbed a bit of hot glue on them to hold them in place. This feather-adorned fabric was sewing to giant shoulder-pads I had made (that were later sewn onto the shirt). There are over 350 feathers. I lost count.
I made a new head/upper-torso armature to sculpt on. Apparently I can no longer sit still, so when my husband was putting plaster of paris bandages on my back, then front, I kept jerking my head back, so the mold came out a little wonky. It was "good enough" for my purposes, so I cast a wonky copy of myself out of cement. I sculpted Ryuk's head over my armature using sulfur-free oil-based clay. I made a two-piece Ultra Cal 30 mold of the sculpt, then cast a latex positive. The mask was painted with acrylic paints mixed with a latex paint base. The wig was "painted" black and glued to the mask. The eyes were made by cutting two ping-pong balls in half and pouring resin into the halves. The middle of the eyes were drilled out, then the entire inside of the eyeballs were dremelled down so the pupils would fit inside them. The pupils were from broken sunglasses that I cut and dremelled down to a circle-ish shape. You could see quite clearly out of them - when they didn't fog up. Almost the various accessories (belt parts, rings) were also sculpted out of clay, then cast in either resin or latex. For a complete step-by-step on how I make my latex/resin masks, please take a look at my Terminator and Donnie Darko instructables (for those curious about resin casting) and my Asari Headpiece and Princess Leia Bikini (if you want to know more about latex casting).
This costume would not have been possible without all the Ryuk cosplayers out there; I looked at many-a-photo before I even started mine, and was delighted to see a enthusiastic crowd of people making this costume. On cosplay.com, QueenToast, SuzzyToast and fly_aguilera have some of the best Ryuks I have ever seen. Ryuk could also not have been done without the help of my husband, who helped bandaged me up in plaster-of-paris, and who helped/was *needed* to help get me into costume. Thanks to Marmbo/Clint Hay for some of the photographs. And thanks to my friend Rachel; it took three of us to transport cement back and forth between locations to make my new head armature!
The entire costume took over 2 solid months to make. I'm still recovering.
First Prize in the
Halloween Photo Instructable Contest
Finalist in the
Halloween Epic Costumes Contest
155 Comments
1 year ago on Introduction
You nailed it. The best one I have ever seen. 👏🥇🏆
2 years ago
I want to make a ryuk cosplay and found yours and it's so amazing! Honestly if mine is half good as yours I would be happy
Reply 2 years ago
You can do it! I'm excited to see yours!
5 years ago
4 years ago, I favorited this 'able and I just noticed I never left a comment.. But hey now I can assuredly say that it's the best looking Ryuk I've seen in at least 4 years. So long as we don't include the actual Death Note art. Hope your still proud :D
6 years ago
Hello, I'm from México City, do you sell it? I'm interested...
Reply 6 years ago
Sorry, this one is already sold! (And I don't make new ones and sell them.)
6 years ago
I know I am hella late, but I am currenyly making a Ryuk cosplay (although not as awesome as yours), and I wanted to ask how you made your teeth. I am stuck between clay and Worbla thermoplastic. O_o
Reply 6 years ago
I made them with "Shrinky Dinks" - plastic that shrinks and thickens as it gets heated up. So following that vein, I would suggest making them out of Worbla (and craft foam)
Reply 6 years ago
Shrinky Dinks! Man, I miss those...nostalgia. Where does the craft foam come into play?
Reply 6 years ago
Craft foam helps strengthen (and bulk up) your Worbla - so you take a piece of thin foam and sandwich it between two pieces of Worbla. Now, since they are just teeth, you may be fine with just cutting them out of one piece of Worbla. Or you may find you have to fold and double-up your Worbla - or it may look best with the foam in the middle. Because Worbla is expensive stuff, I'd say just go for the one piece if it looks right!... actually, I'd probably end up cutting up like a yogurt lid or milk jug; save that precious pricey Worbla!
Reply 6 years ago
(or just skip the plastic stuff all together - get thee to a dollar store and grab a sheet of thin craft foam and cut the teeth straight out of that! In the end what counts for the teeth is how they're painted!)
6 years ago
I'm confused slightly of how you made the bust, and mask.
So you made a plaster cast bust of yourself (using bandage wrap? Then plastering it?), then put cement over or inside the plaster mold?
When you make negative, you line the interior of the cast with Latex? Or does the clay sculpt have to be inside it as well?
You may message me through email: LazaroDrakeDesign@gmail.com
Reply 6 years ago
We made a two part plaster-bandage mold of my head - it's not bandages that later have plaster slathered over it, it's bandages that already have plaster embedded in them. Like what the doctors would use for putting a cast on a broken bone. Just using regular plaster can be dangerous.
Into that two-part plaster-bandage mold, you pour the Ultra Cal 30 (as a result, you get a "cement" head cast/bust).
On top of the bust, you sculpt a mask out of clay. Then you make a two-piece mold of the sculpture out of Ultra Cal 30 and cheesecloth/burlap.
You remove the two-piece mold from the clay sculpt/bust, clean out any remaining clay from the mold, then do a final positive cast of latex - and that's your mask.
For even more detailed steps, with pictures, please look at my other instructables that cover life-casting:
Liara Headpiece https://www.instructables.com/id/How-to-Make-An-Asa...
(plaster-bandage head mold, ultra-cal 30 bust, clay sculpt, ultra-cal 30 mold, final latex headpiece)
Terminator Eyepiece https://www.instructables.com/id/Terminator-Eyepiec...
(plaster-bandage head mold, ultra-cal 30 bust, clay sculpt, silicone and plaster-bandage mold, final resin headpiece)
Horned King Mask https://www.instructables.com/id/Horned-King-Mask-F...
(alginate and plaster-bandage head mold, ultra-cal 30 bust, clay sculpt, ultra-cal 30 mold, final latex headpiece)
Hope that helps!
6 years ago
But how do you sew everything together tho? :(
Reply 6 years ago
With a sewing machine! :D
I made a mockup of both the shirt and pants using Burda 7742 and McCall's M6173. You're supposed to use stretchy material for those patterns, but I used a non-stretch fabric for my mockups, and used less than 4 1/2 yards of fabric for that.
For the shirt (as an example) I put together a basic top using the pattern pieces provided - so you're sewing two arms, a front half and a back half together. Then I tested that on my body to see how that fit - keeping in mind that a zipper would be going on the back, so the shirt can fit tightly. Once pleased with the fit, I drew a patch-work pattern on the shirt, and cut out those pattern pieces, labeling them as I went (so you knew what would be sewn to what). Then, adding a seam allowance to all the pattern pieces, I cut them out of leather and then stitched them together!
If that all still has you going 'huh?' ... do a simple sewing project for practice (and there are lots of tutorials online/here that will get you started)
Reply 6 years ago
Thanks. Seems this is beyond me you. I haven't a clue about sewing, don't own a sewing machine, cant afford one.
Reply 6 years ago
Don't let that discourage you - there's youtube, the library, even classes on Instructables, that will teach you how to sew! Just think of how cool it is to learn how to do something new.
6 years ago
Hi, I was wandering about the feathers you used. Ive searched for feathers online and there are so many selling any different species of feathers. Did you use a specific feather from one animal or is there a specific "costume" feather you would recomend?
Reply 6 years ago
I ordered 200 (4 sets) of 6-8inch saddle rooster feathers (from here http://www.ebay.com/itm/NEW-50pcs-Saddle-Badger-Rooster-feathers-6-8-inch-Multicolor-colours-Optional-/200721003404?ssPageName=ADME:L:OC:CA:3160) plus 100 of 12-14inch saddle feathers (the store I got them from is no longer up, but you should be able to find them on ebay)
6 years ago
Hi,
You have the best Ryuk ever! I'm a noob at all this, and was wondering if you could give me some guidance on creating the shoulders. I was wondering if there's a specific type of shoulder pad I should buy? Or a specific type of fabric I should get that I would be able to pull feathers through?
For example, out of this list, is there a specific type of shoulder pad that you'd suggest?
http://www.ebay.com/sch/i.html?_from=R40&_trksid=p...
Thanks a lot, and Happy Halloween!